libera/#maemo/ Sunday, 2020-06-07

MaxdamantusWhoops, dropped my N900 in a bucket of water.03:21
MaxdamantusGoing to blowdry it with the motherboard taken out. Most of it is still dry. I reckon the display doesn't need to be disassembled.03:29
sunshaviMaxdamantus: too bad. I hope You could it working again03:31
MaxdamantusPretty sure there's not going to be anything wrong with it.03:32
MaxdamantusI got it out within around 10 seconds or so, phone was still on. Took the battery out very soon after that.03:32
Maxdamantusand have now dissasembled it and blown dry the main board.03:32
MaxdamantusGonna leave it to air dry now for a couple of hours.03:41
MaxdamantusAnd booting it again now. I guess a bit earlier than I said.05:00
MaxdamantusHm. Actually, it looks like the bq27200 state got reset.06:35
MaxdamantusWonder if that was because of the water.06:36
MaxdamantusIt has LMD at 2056 mAh, which I think is the default, and "total cycle count since last full reset" is now 0.06:36
MaxdamantusIt also has CSOC 0% even though the reported voltage is aroun 4.9 V.06:46
Maxdamantuser, 3.9 V*06:54
* enyc meows10:00
enycMaxdamantus: dhevel quite understood the bms-monitoring when used with replaceable batteries myself...10:00
siceloMaxdamantus: bq27200 does get reset when battery is out10:00
KotCzarnydead pupbat?10:01
KotCzarny:)10:01
sicelobupbat doesn't do bq27200 iirc. it does time/rtc10:02
KotCzarnypity10:02
KotCzarnyalthough understandable if batteries dont report serial numbers10:02
Maxdamantussicelo: hm. I don't think that's right.10:12
Maxdamantussicelo: when I say "reset", I mean a full reset, where all the values go back to what's in the EEPROM.10:13
Maxdamantusie, that "full reset" counter goes back to 0.10:13
sixwheeledbeastWould normally be best to dry it over a good few days, although you did say you disassembled it.10:13
MaxdamantusI think it was at something like 130 before, so it very definitely does not get reset when the battery is taken out.10:14
sicelomaybe DocScrutinizer05 will confirm. i think it will go back to 0 for sure10:17
MaxdamantusI guess I can try on another device.10:18
siceloI don't remember how long it takes to 'reset', but it does :-)10:19
sixwheeledbeastThere is likely some factiod or wiki with that info.10:20
MaxdamantusMeh, need to install things on the other device I have at hand, can't be bothered getting out one of the other devices.10:23
DocScrutinizer05sicelo: right, and it takes a few minutes iirc22:45
DocScrutinizer05bupbat doesn't help keeping values in bq27k22:46
DocScrutinizer05~listvalues bq2722:47
DocScrutinizer05gosh22:47
DocScrutinizer05....22:50
DocScrutinizer05*crickets*22:50
DocScrutinizer05~listvalues bq2722:52
infobotFactoid search of 'bq27' by value (5): calibratebq27200 #DEL# ;; bq27200 ;; bq27k-detail ;; bq-calibrate ;; bq27.22:52
DocScrutinizer05~bq2722:53
infobotit has been said that bq27 is http://maemo.cloud-7.de/maemo5/usr/local/sbin/ bq27*, or http://maemo.cloud-7.de/maemo5/patches_n_tools/22:53

Generated by irclog2html.py 2.17.0 by Marius Gedminas - find it at https://mg.pov.lt/irclog2html/!